IronHeadIronHeadRestore · Preserve · Ride

The IronHead Journal · Restoration

Norton Commando Restoration: Isolastic Shims, the Layshaft Bearing and the Jobs That Actually Matter

A Commando restoration is not twenty jobs of equal weight. Three of them decide whether the finished bike is the smooth, sweet-handling machine Norton designed or a vibrator with a wandering rear wheel: the isolastic mounting system that carries the whole drivetrain, the gearbox layshaft bearing that carries a deserved reputation, and the swingarm and cradle inspection that ties them together. Do these in the right order, with measurements instead of opinions, and the rest of the restoration is ordinary work.

First, understand what the isolastic system is doing

The Commando's engine, gearbox, and swingarm are not bolted hard to the frame. They sit in one cradle assembly, mounted to the frame through rubber isolastic units at the front and rear. The rubber is the point: a big parallel twin shakes, and the isolastic mounts let the drivetrain move a controlled amount while the frame — and the rider — stay calm. That is why a healthy Commando feels impossibly smooth for 1968, and why the system is a wear item with an adjustment, not a fit-and-forget part. (Our Commando buying guide covers checking a bike you do not own yet; this piece is for the one already in your garage.)

Job one: measure the isolastic clearance, then shim it

The mounts work only when the side-to-side clearance between the isolastic housings and their frame abutments is in spec. The clearance is set with shim packs behind the mount collars, and it is measured with feeler gauges — slipped into the gap at the front and rear mounts, both sides, with the bike supported so the drivetrain hangs honestly. Too much clearance and the whole drivetrain steers the rear wheel by small, unwelcome amounts: the classic Commando weave at speed and a bike that will not hold a line. Too little and the rubber cannot work, and the vibration the system exists to absorb arrives at the bars and pegs undiminished.

The working discipline matters more than the number: clean the abutment faces before you measure, measure at several points around each mount, write down what you found before you change anything, and shim in small steps, re-measuring as you go. Your year and model's factory service literature carries the clearance figure and the shim procedure — work to that page, because the figure is the whole job. Vernier-type adjustable isolastic kits exist and replace shimming with a threaded adjustment; they are a legitimate upgrade, but they reward the same measured approach.

Job two: the layshaft bearing, before it introduces itself

Inside the Commando gearbox, the layshaft rides in a ball bearing that has been the box's known weak point for decades. When that bearing collapses — and on an original bearing it is a when, not an if — the layshaft drops, the gears misalign, and the gearbox can lock. On a restoration, the bearing is not inspected and pronounced fine; it is replaced as a matter of course while the box is apart, and the standard, well-proven replacement is a roller bearing of the correct specification, which carries the load the ball bearing could not. This is the cheapest insurance in the entire motorcycle: the box is already open, the bearing costs little, and the failure it prevents costs a gearbox — or worse, at speed. While the box is apart, the rest of the inspection is conventional: gear dogs and selector forks for wear, bushes for play, and every seal renewed.

Job three: swingarm, cradle, and head steady

The swingarm pivots on the cradle, and its spindle and bushes wear with the same mileage that wore the mounts. With the rear wheel off, check for side play at the spindle before you blame the isolastics for handling sins — the two systems present similar symptoms and are cheap to confuse. The cradle itself deserves a straightedge and a close look at the mount tubes and welds. Up top, the head steady (the engine-to-frame brace at the cylinder head) is part of the same controlled-movement system: its rubbers and hardware get renewed and set with the isolastics, not after them, because all three pieces share one job.

The order, and what surrounds the big three

Sequence the restoration so the chassis work happens with the drivetrain accessible: strip and inspect the cradle and mounts first, set the isolastic clearance with the engine and box in place, do the gearbox bearing while the box is out or open, then hang the swingarm and set its spindle. Around those three, the familiar Commando work arrays itself: the primary chaincase and its oil seals, the Amal carburetors (slides and pilot circuits wear long before the bodies do), the Lucas electrics answered with clean grounds and honest connections rather than replacement looms by default, and brakes matched to the model — drum on the earliest bikes, disc on the later ones, with the Mk III's electric start and left-foot shift making it the most civilized of the line.

Done in this order, a Commando restoration stops being a gamble on an old bike's manners and becomes what it should be: a short list of measured jobs, each with a number attached. And if you are still shopping for the bike this work gets done on — or you want the year-by-year changes and the full inspection list in one place before the wrenches come out — the library's companion volume is the Norton Commando 750/850 Buyer's Guide.

IronHead · Des Moines, Iowa

Get the IronHead letter

New guides, workshop notes, and vintage-bike tips as they're ready — plainspoken and occasional. Unsubscribe anytime.